Smog Check OBD II (OBD 2) : What are Readiness Monitors ?

check engine lightOBD II, “CHECK-ENGINE” LIGHTS,  and READINESS MONITORS..WHAT ARE THEY?

OBD II is a system that has been installed in most 1996 and later cars and light trucks, intended to inform the driver of problems in the components that control the engine and transmission. The primary reason OBD II was invented is to reduce smog emissions caused by malfunctions, but it is also valuable as an alert to the driver that something is wrong…something that can affect gas mileage and drivability, or actually cause further damage to the vehicle.

While you are driving your vehicle, its computer is constantly monitoring and running tests on the various sensors, actuators and electrical parts that make the car run properly. If a problem is detected, a Diagnostic Trouble Code (DTC) is set, and the computer turns on the “Check Engine” light. (The light may say “CHECK ENGINE”, “SERVICE ENGINE SOON” or merely be an icon that looks like an engine.)

What are “Monitors”?

Even if there are no problems with your car, the results of tests that have been run are stored in the computer as having been completed. The status of these tests (complete or incomplete) is referred as the “readiness monitors”.  When your car gets a smog test, one portion of the test involves connecting the smog test machine to the car’s computer and checking if there are any DTC’s, and also checking to see if the monitors are ready. If they are not, the vehicle fails the test, because there may be problems in the system that can’t be reported by the computer.

There are several reasons why the monitors may be incomplete. If your car has recently been repaired for a problem that set a DTC (check engine on) and the technician cleared the DTC, he also erased the monitors. Also, if battery has been disconnected, replaced or needed a jump-start, the monitors may be erased.

In earlier systems (OBD I) there was no long-term record stored of the state of the car’s systems. If a problem turned on the check-engine light, a simple battery-disconnect could turn it off long enough to pass a smog test, even though the problem was still there.  OBD II helps ensure that the vehicle is in proper condition to run clean.

My car passed the emissions test…who cares if the monitors are incomplete?

The overall smog inspection consists of three parts…the emissions test,  which measures the smog coming out of the tailpipe; the visual inspection, to look for broken or modified parts; and the functional tests, where other systems are checked to see if they are working properly. The OBD II test is a functional test.

As sophisticated as the emissions test has become, it still only tests your car under very limited conditions… accelerating at 15mph and cruising at 25mph, with the engine warm. It does not test what is going on when the engine is cold, idling, decelerating, etc. Also, not all the smog a car makes comes out the tailpipe. Gasoline fumes that evaporate from your fuel tank, and crankcase fumes that collect in the lower part of the engine can escape into the air and create smog. The systems that control these are not tested during the emissions test, so the visual inspection and OBD II test are needed to check them.

OK, my monitors are incomplete…how do I complete them?

Basically, drive the car. There are specific driving conditions that must be met in order to run various tests, but most of them can be met in normal driving. One thing that helps is to cruise at a steady speed for several minutes, so a ten-mile freeway drive in light traffic is a good bet. Keep a steady foot on the gas rather than speeding up and slowing unneccesarily.

Note that a car can pass with some incomplete monitors…a maximum of one on 1999 and earlier cars, and only one (The Evaporative System monitor) on model year 2000 and later gasoline powered automobiles.

All monitors must be complete on 1998-2006 diesel powered vehicles.  Any two (2) monitors may be incomplete on 2007 and newer diesels.

Some tests only run when the car sits overnight, or is allowed to cool down for several hours. Most cars will complete the monitors easily with the above methods, but rarely it will take up to several weeks before they are complete. Some auto repair shops will run drive cycles, a specific driving routine, to complete monitors more quickly.

My mechanic told me my check engine light is on because of a short circuit in the light, and there is nothing wrong with the emission system.

Though this may be true (rarely), the check engine light is part of the emission system and needs to be working properly for the car to pass. If it has a short, the short must be fixed.

OBD Testability Issues

Some vehicle models are known to have issues that interfere with the successful completion of OBD readiness monitors.  The State of California Bureau of automotive repair maintains a list of these vehicles and specific remedies, if known, that can assist a motorist in completing monitors.  In some cases repairs may be required, and in others test equipment is programmed to ignore some or all readiness monitors on affected vehicles.

To learn more about OBD readiness monitors and testability issues, please download the Smog Check OBD Reference from the Bureau of Automotive Repair website.

126 Replies to “Smog Check OBD II (OBD 2) : What are Readiness Monitors ?”

    • Julius

      It depends on what you mean by “fails monitor test”. If you mean that your 1997 Sonoma is not completing the EVAP monitor (Not ready, incomplete, etc), that is the only incomplete monitor, and nothing else is wrong with your vehicle, then yes, it can pass the smog inspection. If you mean that the monitor runs, and sets a DTC (Check engine light comes on), then no, it will not pass until it is repaired.

      Reply
      • Enrique

        hellow julius i recently replaced the battery in my car and no check engine light was on and then the check light came on so i hooked a scanner and all monitors were incomplete after driving the car the monitors are now ready except one the evap so as far as you know will the check engine light come on is the evap monitor is showing incomplete on a 06 honda accord 2.4 will the check engine light turn off when the evap monitor is ready because there was no check engine light on untill a replace the battery ?

        Reply
        • dewok Post author

          Enrique

          If all monitors are ready except evap and there are no fault codes, then your vehicle is ready to pass a California smog check.

          As for for the previous check engine light, was the fault code related to the evap system? If so, then yes, it is likely that the MIL will illuminate once the evap monitor completes to ready.

          Reply
          • Enrique Diaz

            no there was no check engine light on before…..the only reason i replaced the car battery because the green eye/lenses on the battery had gone from a bright kinda neon green to just plane dark green so it was still under warranty so i change the battery and then the check engine light came on.

    • Lew

      Got it fixed ! ! The garage guy said drive it and come back, I did and it still would not pass – so I kept driving across the boarder into my uncles house in Oregon ! No smog and out the door for $60 bucks and I’m from the Tree State! Stick you Ca DMV up your tailpipe !

      Reply
  1. JACK HUDSON

    My 2001 Chevy van has less than 3000 miles on it and the battery needed replacement, so I have been trying to put some miles on the odometer; however, driving on the freeways is a “joke” as to steady speed data storage.

    If my truck has always been able to pass prior year’s tests, why is a “STAR” certification required this time?

    Resp,
    Jack

    [Editors Note: Original comment was retyped, but not changed, to improve readability.]

    Reply
    • Julius

      The Bureau of Automotive Repair directs a portion of vehicles requiring a smog inspection to STAR certified stations. (Both licensed
      Test Only stations and licensed Test and Repair stations may qualify for STAR certification).
      Currently, these directed vehicles fall under two categories:

        High Emitter Profile – The High Emitter Profile (HEP) is a statistical model used to identify vehicles more likely than others to fail a Smog Check inspection. Vehicles identified by the HEP must receive certification at a STAR certified Test Only station or STAR certified Test and Repair station.

        A vehicle that “has always been able to pass” may still be included in the “High Emitter Profile” group. That’s because High
        Emitter refers to the year, make and model instead of a specific vehicle’s performance.

        2% Random Sample – For program evaluation purposes, 2% of the vehicles in Enhanced Areas are randomly selected for certification at a STAR Test Only station or STAR Test and Repair station. Directed vehicles can only receive Smog Check certification from STAR Test Only or STAR Test and Repair stations.

      Either way, the important thing to remember is that there should be absolutely no difference between a smog inspection/test performed at a STAR Station and an inspection/test performed at a “regular” shop. The only difference is that in order to inspect and certify directed vehicles, a STAR station is required to meet stricter performance thresholds than “regular” smog shops.

      Reply
  2. Dave Pulcini

    Thank you for explaining the smog check process in simple terms….I’ve gone nuts trying to understand why the tailpipe emissions are not enough,never really understood “Functional” testing.

    Reply
  3. samantha

    i went to get my truck smogged and everything passed but the OBD system checks fails, so the smogg guy told me to go and drive it around, so i did. i did well over 40 miles, drove it all weekend to different cities and i took it in monday morning, and its still not working. my check enegin light has not came on, and he asked if i had needed a jump or unplugged the battery, i said i have not, and he stated that my computer in the truck keeps reseting itself. its a 98 ford ranger, and im kinda stuck from here on what to do.
    is it fuse oe sencer that needs to be replaced or what.?
    hope yoou can help

    Reply
    • Julius

      Hi Samantha, I’m sorry that your truck is having difficulty completing OBD II readiness monitors. I understand how frustrating that can be.

      While most vehicles complete monitor readiness in a short amount of time during normal driving, other vehicles can present more of a challenge.

      In some cases its a matter of driving habits. Most monitors run during steady driving conditions while others (The catalytic converter monitor on some many vehicles) require stop and go traffic.

      You could try looking on line for OBD drive cycles specific to your year make and model vehicle.

      Also, some vehicles are known to have OBD testability issues. The State of California Bureau of Automotive repairs maintains a list of these vehicles in a PDF document located at http://www.bar.ca.gov/pdf/Smog_Check_OBD_Reference_Guide.pdf.

      It’s also possible that a defective component in your vehicle may be preventing your vehicle from completing readiness monitors. Your best bet is to take your vehicle to a qualified smog “test and repair” shop where they can diagnose the cause of the problem and repair your vehicle. You can find a list of repair shops at http://www.smogcheck.ca.gov/pubwebquery/station/stationlist.aspx.

      Reply
      • Jacquline swift

        Hello , I have a 2000 C230 Mercedes benz kompressor. I have been trying to smog I drove over 1000 miles and still the smog tech said that it’s saying not ready. I have been back to him 3 times . And still not ready . Any thing I can do ? Please help . Thanks

        Reply
        • dewok Post author

          Hello Jacquline, One trick that we have found for completing Mercedes drive cycles is to drive with A/C off. You also want to allow the vehicle to warm up in the morning at idle (10-20 minutes) and do highway driving (steady speed @ 60mph without braking for 10 minutes). At the end of the drive allow it to idle in park for 10-20 minutes.

          Reply
    • Adolfo retuya

      You don’t have to drive around . You have to find out the drive cycle for your car and follow it strictly. For example my Toyota it says drive 10 miles at 25miles per hour then 5 miles at 50 miles per hour. No braking. Do it in the freeway at 2 am less cars because 25 miles is real slow . No braking!

      Reply
  4. Ken

    I have a 2004,the codes and monitors were cleared by the smog tech by accident,I hear there’s o button on OBD that will do that, I have tryed 3 different drive cycles I found from smog techs, online and GM dealer, I’ve also been driving it daily and logged up 2500 miles over the last 2 months, what the heck am I suppose to do

    Reply
    • Julius

      While the BAR OIS does not have a button “that will do that”, it’s possible that he was using a handheld scanner that would.

      In addition to following the specific drive cycle recommended by the manufacturer for your year, make, and model vehicle, you also want to ensure that there’s not another issue with your vehicle that is preventing the monitors from running to completion.

      After 2,500 miles without success, I’d suggest taking your vehicle to a qualified emissions repair technician who may be able to diagnose your vehicle’s problem.

      Reply
  5. meesha

    i just got catalyst system maintained and cleared but my light popped back on with the same code my mech said that it might be on due to the fact that its still clearing from the old leaks and should go off and my car keeps rejecting the emission test what should I do .
    ?

    Reply
    • Julius

      Meesha, based on the information that you provided, it’s not possible for me to provide answers specific to your situation, but generally speaking it is not likely that the “light popped back on… due to the fact that it’s still clearing from old leaks”. Unfortunately, it is also unlikely that the light will “go off” without further repairs.

      Most diagnostic trouble code setting faults are “two trip faults”. In the case of a two trip fault, the first instance of the fault does not turn on the check engine light. Instead the details of the fault are stored in memory pending a repeat of the same fault under similar conditions. The check engine light does not come on until the second time the fault is detected.

      Assuming that your mechanic cleared (turned off) the check engine light after repairing your vehicle, your vehicle’s on board diagnostic system would have no memory of “old leaks”. Even if old data remained, your vehicle’s computer would wait until it detected the same fault a second time before turning on the check engine light. To make a long story short, an old problem will not turn on your check engine light.

      Reply
  6. jerry

    I tryed to do a smog on my car n they say its good but when they try to finish up the test they saying its not finishing up an it stops at 91% n wont finish it up to print the smog paper why is it doing that?

    Reply
  7. silke

    I just came back from the smog and the cat said its not ready. Everything else was. The mechanic said I need to drive more miles, but I have driven about 1.5k miles within a month. The mechanic said that’s the only way to pass the smog. However my car is from 2000 and I am trying to find how many monitors I am allowed to fail and if that would qualify…
    Thanks for your help!

    Reply
    • Julius

      In order to pass the smog inspection, only the EVAP monitor can be incomplete on model year 2000, and newer, gasoline powered vehicles. The state does make allowances for certain vehicles that are known to have testability issues that prevent monitors from running to completion (Read more about OBD II Monitors and Testability Issues here). However, in most cases, after 1,500 miles of driving, I’d suspect that a defective component is preventing the catalyst monitor from running to completion.

      Reply
  8. Philip

    Hey..I just bought a 2001 Mitsubishi Eclipse GT but the guy said it won’t pass smog and it needs to be driven longer…I drove it about 60 miles back home(plus whatever he did) and when I got home I swapped the battery…I was told that me doing that reset the drive cycle and it still won’t pass so what do I need to do to find out what the [actual] problem with my car is??? Please and thank you

    Reply
    • Julius

      Unfortunately, completing OBD II readiness monitors on 2001 Mitsubishi Eclipse model vehicles can be extremely difficult. Mitsubishi has issued a technical service bulletin (TSB) detailing this problem and drive cycle suggestions for running the monitors to completion (Available here).

      It is important to remember that disconnecting the battery, clearing the computer, resetting diagnostic trouble codes, or any other action that interferes with your car’s “computer memory” will result in your having to “start over”.

      Reply
  9. Andre

    My 2004 Toyota Highlander has a CAT sensor that has not reset after disconnecting the battery several months ago, and will hence not pass the smog. The model is listed in Table 3 of the OBD reference guide with the cause listed as “Monitors can be difficult to complete.” Since the model is listed in Table 3, does that mean I can get an exemption? If so, is this something that can be done at the original test station or do I need to take it somewhere else?

    Reply
    • Julius

      Hi Andre, I took a look at the Smog Check OBD Reference, and while it does indicate that “Monitors can be difficult to complete”, the “Instruction to Inspector” column indicates “Follow drive cycles in Toyota service information. Test normally”. So, unfortunately, it does not appear that BAR would issue an “exemption” for your vehicle.

      CATALYST MONITOR DRIVE CYCLE INSTRUCTIONS

      1. The monitor will not run if active diagnostic codes are present
      2. Do not turn off the ignition switch during the test procedure.
      3. Allow the vehicle to run at idle until fully warmed up. I usually recommended letting it idle for ten to fifteen minutes after sitting overnight.
      4. After warming up the vehicle, drive at a steady speed between 40 & 70 miles per hour. Tip: try to stay around the middle of this range (55MPH). Also, in Southern California, it may only be possible to maintain these speeds early on a weekend morning.
      5. You may need to extend the drive cycle.
      6. In most cases, you should be able to complete the catalyst monitor after following the drive cycle a couple of times.

      If several reasonable attempts at running the drive cycle fail to complete the catalyst monitor, a problem may exist that is preventing your vehicle from running the monitor to completion. In that case, it may be time to have your vehicle properly diagnosed and repaired by a shop that has the training, equipment, and experience necessary to diagnose and repair OBD monitor issues.

      Reply
  10. Pingback: monitor is not ready! - Toyota Sienna Forum - siennachat.com

  11. Dulce

    Hello,
    I have a Toyota Corolla 1998. My battery was stolen over a month ago. I put a battery 3 weeks ago. I been driving the car for 2 weeks already. They day I went to do the smog check my car didn’t want to turn on. I noticed that holder came off. I put it back and didn’t drive it for 3 hours. Then I went over to the smog check place which was across the street where I was. The car didn’t pass the OBD section. The guy told me to drive that car for 80 miles. I haven’t yet. Do I have to drive all 80 miles?

    Reply
    • Julius

      The simple answer is maybe. Eighty miles is a good rule of thumb because most cars will complete OBD readiness monitors within eighty miles; however, many cars will complete them in less, while some can take a whole lot more. One solutions would be to purchase an inexpensive code reader and check monitors as you go.

      Reply
    • Don Elder Sr

      Yes, but also, some vehicles will reset/clear monitors when vehicle is turned off. Recommend on vehicles prior to 2001 to drive at least 50 miles and before turning off vehicle have shop scan OBII for proper monitor operation. If ok, shut off vehicle and recheck later to see if monitors have preformed it’s diagnostics and maintained memory. If not, dive 40-50 miles and recheck and smog. DO NOT TURN OFF VEHICLE. This should work. Later OBII systems retain prior drive cycles information and scans sensors and monitors faster due to processor. Understand that earlier EEC systems have to learn as you drive and monitors are operated in a series, until all emission, fuel and engine sensors are operating properly.

      Reply
  12. Frank Baltazar

    I have a 2004 suburban, it failed the state inspection because the Catalyc and Evap sensors were not ready. I had not done any repairs or disconnect the battery, so I took it to the dealer where they did a drive cycle and on the paper work it said that the drive cycle was completed and both monitors were ready. I drove directly to get the inspection done and it failed again for the same symptom. I took it back to the dealer and they told me that somehow monitors were resetting, so they were going to do more tests. Now they said that the catalyst converter is defective and needs to be replaced. Will a defective Catalys convereter cause the ECM to reset the monitors? If the catalyst was defective I would think the service engine light would come on and stay on alerting of an issue with the catalys. Any thoughts?

    Reply
    • Julius

      Frank, I’m inclined to agree with you. OBD II is designed to function exactly as you described at the end of your comment. I’d be more inclined to believe that something else is causing the monitors to reset (Low cranking voltage, or other factors that may interrupt power to the PCM), or that the dealer inadvertently failed to complete monitors the first time.

      Reply
  13. Jose antonio

    Hello Julius,

    My 2000 Toyota Camry did not pass smog. I live at Concord, California. The technician asked me to do a full drive cycle which I did for 2 weeks. I almost drove 100 miles. I am using OBD 2, From the 2 Incomplete it went to down to one. My check engine light is off. The technician is saying that the next time he checks my car and with one incomplete, he told me to bring it to a mechanic.

    Please help. There is no error code on my the reading of my OBD 2. I am using Actron CP9125

    Reply
    • Julius

      While 1999 and older model year vehicles can still pass the smog inspection with one incomplete readiness monitor, only the EVAP monitor can be incomplete on 2000 and newer model year vehicles.

      Allowing that you are meeting the requirements of the Toyota drive cycle, it sounds like the technician is giving you good advice. Start with the monitor that is not running to completion and look for issues that would affect that specific system.

      Reply
  14. MIGUEL BRAVO

    BUEN DIA SOY DE MEXICO Y ESTO DE LOS MONITORES ESTA LLEGANDO POR ESTE LADO ,,, MI PREGUNTA… HABRA UN SIMULADOR O ALGUN APARATO QUE EN LUGAR DE CONECTARSE AL OBD DEL VEHICULO ,, SE CONECTE AL SIMULADOR Y PASE LOS MONITORES LISTOS??…

    Reply
  15. Kenneth Mccarthy

    Hello,I have a 2005 Nissan Frontier SE and I added dual exhaust paid $700 and ever since check engine light comes on,I bought a $300 programmer so I can clear the light but wouldn’t pass inspection still and the light comes after 75 miles,my garage wants all most $3000 to fix it because they say it’s the catalyst converter and the sensors,the cleared it last year but it cost me $250 to get the sticker and they said they did a fuel injection flush but I believe they didn’t and light cam back on after 75 just like my programmer did.Any advise would be greatly appreciated,thank you Kenny

    Reply
    • Julius

      Hi Kenneth, it sounds like you have enough going on with your vehicle that your question is beyond the scope of what we can address over the internet. Hopefully everything works out in the end.

      Reply
  16. Linda

    My 2003 Dodge Caravan was given an incomplete on all parts of the smog check in NV, I was told to drive the vehicle and come back. I drove 2600 miles and then went for a recheck a week later and it came back with an incomplete again. I was then told to drive it for about 60 miles and come back again. What could be causing an incomplete? I had recent repair done a week before the 1st smog check, could something have been disconnected to cause this?

    Reply
    • Julius

      Hi Linda, sorry about the late reply.

      I’m assuming that the check engine light is not on, so it’s a safe bet that nothing was left disconnected.

      You want to make sure that you’re following the manufacturers suggested drive cycle for your vehicle, and that there are no active recalls or campaigns related to your vehicle. In many cases, especially with Chrysler vehicles, the manufacturer periodically issues firmware updates in order to address issues related to the car’s “computer”. Such issues can often prevent monitors from running to completion.

      Also, your mechanic may be able to diagnose a problem that is on the verge of turning on the check engine light, but isn’t quite there. A component that is close to failure can delay or prevent the completion of readiness monitors. Just mention mode six data to your mechanic. If he gives you a glazed look, consider having the problem diagnosed at another shop.

      Reply
  17. Jose Antonio

    Hi Julius,

    I have a 2000 Toyota Camry. I went to check it with my OBD11 and found the following:

    0 (zero) error code
    2 Incomplete
    6 ready

    Is my car going to pass smog this time?

    Reply
    • Julius

      Assuming that you are in the State of California, the answer is no.

      The EVAP monitor is the only incomplete monitor allowed on 2000 and newer gasoline powered vehicles.

      Reply
  18. Bob

    I have a 1999 Chevy Prizm (Corolla) with CAT and EVA monitors both not ready after erasing codes. I got EVA ready easily last time I did this, but no luck this time. Someone mentioned gas tank level might be a factor, your thoughts?

    Reply
    • Julius

      The EVAP monitor is often a difficult monitor to run to completion. For that reason, in the State of California, 1996 – 1999 model year gasoline powered vehicles can pass the OBD II functional portion of the smog inspection with any one incomplete monitor, while 2000 and newer can pass if EVAP is the only incomplete monitor.

      Factors that can affect the EVAP monitor can include ambient temperature and fuel level. In most cases the EVAP monitor will not run if fuel level is below a quarter tank, or above three quarters of a tank.

      Reply
  19. Michael

    Hello I have 2006 chrysler Sebring touring and my o2 sensor and Cadillac converter sensors aren’t reading ive replaced a battery and computer around 7 months ago I have driven everyday since then…was told recently to drive an extra 50 to 70…so I ended up driven close to 150 city and freeway but those sensors still arent ready…it was three but now its down to two…my registration is well over due so driving is high risk for pull over and possible tow..also I have no check engine on…can u give me some advice please

    Reply
    • Julius

      Hi Michael;

      You and Linda have similar issues (The comment above yours).

      As I suggested to Linda, you want to make sure that you’re following the manufacturers suggested drive cycle for your vehicle, and that there are no active recalls or campaigns related to your vehicle. In many cases, especially with Chrysler vehicles, the manufacturer periodically issues firmware updates in order to address issues related to the car’s “computer”. Such issues can often prevent monitors from running to completion.

      Also, your mechanic may be able to diagnose a problem that is on the verge of turning on the check engine light, but isn’t quite there. A component that is close to failure can delay or prevent the completion of readiness monitors. Just mention mode six data to your mechanic. If he gives you a glazed look, consider having the problem diagnosed at another shop.

      Reply
  20. Andrea

    What are the names or abbreviations of all the readiness monitors I need to pass? By the way I have a 2001 Mercury marquis.

    Reply
    • Julius

      Hi Andrea,

      Abbreviations will vary depending on the scanner or code reader that you are plugging into your vehicle’s diagnostic data connector; however, the important thing to remember is that in order for your 2001 Mercury (And most other 2000 and newer gasoline powered vehicles) to pass a smog inspection in the State of California, the EVAP (Sometimes abbreviated as EVA) monitor is the ONLY monitor that can be incomplete.

      Reply
  21. carlos v

    have a 2004 dodge ram 1500 5.7 hemy replaced my egr valve yesterday and went to get smoged today didnt pass due to obd monitor not ready evaporative system what do i do next.

    Reply
    • Julius

      Basically, drive the car. There are specific driving conditions that must be met in order to run various tests, but most of them can be met in normal driving. One thing that helps is to cruise at a steady speed for several minutes, so a ten-mile freeway drive in light traffic is a good bet. Keep a steady foot on the gas rather than speeding up and slowing unnecessarily.

      Note that a car can pass with some incomplete monitors…a maximum of any one on 1999 and earlier cars, and only one (The Evap System monitor) on model year 2000 and later gasoline powered automobiles.

      Reply
  22. Richard m

    My 2000 Dodge Grand Caravan continues to fail the readiness part of the smog test. Can I retire the car via the cash for clunkers program?

    Reply
    • Julius

      Yes, if you meet the program requirements, you could retire your vehicle on the Bureau of Automotive Repair’s (BAR) Consumer Assistance Vehicle Retirement Program. You can learn more about BAR’s Consumer Assistance Program here and here. here.

      Reply
  23. Jeff

    03 acura rsx type s. I have question, i bought the car to a friend of mine and the car hasn’t move or drove for a year. But he replace the battery already so i took the car to do smog and it fails. Everything else pass except OBD2 not ready. Smog guy told me to drive cycle so I drove the car and added only 15 miles to the car. idk if i should drive it more miles or what. Can you help me and explain it?

    Reply
    • Julius

      We normally recommend that customers run through the drive cycle two to three times; however, on a late model Acura you should be able to check if your vehicle is ready to test by following these steps:

      • Turn the ignition to the ON (II) position without starting the engine
      • The MIL (Check Engine Light) will come on for 20 seconds
      • After 20 seconds, one of two things will happen. It will either go off, or it will blink five times.
      • If it goes off (Without blinking five times) your vehicle should be ready to test.
      • If the check engine light blinks five times before turning off, continue to run the drive cylce. Your vehicle is not ready to test
      Reply
  24. Jeff

    Thanks! It blink five times and i guess it’s not ready for test. So How far or many miles am i supposed to do the drive cycle? And do i just keep driving even though it’s not 55mph? Can you tell me the step how to do drive cycle?

    Reply
    • Julius

      Which monitors weren’t ready when you had the vehicle tested. The monitors that weren’t ready should be listed about two thirds of the way down on the inspection report.

      Reply
  25. Stephanie

    I drive a 2010 Toyota Corolla. Went to get a smog and it failed the emissions. Even though the smog failed at the test only station, can I go to another no test station to get the smog again? Or does the information go to DMV already as he’s doing the test?

    Reply
    • Julius

      Hi Stephanie,

      A common misconception among people whose vehicles fail a smog inspection is that they have to go back “and finish” the test. The truth is that the failed test is finished. The car failed. In other words, he is no longer “doing the test”, so you can take your car to any smog test station you would like; however, if you were directed to take your car to a “STAR Station” (SMOG Certification Required at a STAR station, or in some cases some DMV paperwork still says “test only”), then you need to make sure to go to a STAR station.

      No matter where you take it (Even if you return to the original station), a new inspection will be performed from start to finish.

      Reply
  26. Jeniece Smith

    Hello, I just took my car to get smogged today I got my oil changed first then took it to get smogged, I drove my normal route to work which is approximately 15-20 min from home and then to get my oil changed another 15-20 min then to get it smogged 5 min away. They said I didn’t pass smog because my it wasn’t ready yet stating it couldn’t read it yet. I don’t have any check engine light on or any lights that could cause it to fail. After they told me to drive it and bring it back I drove it for about 10-30 min and brought it back and it still wasn’t able to pass still saying it wasn’t ready? May anybody here know why?

    Reply
    • Julius

      We have a several good articles here at the Just Smogs® blog that explain readiness monitor failures (Smog Check OBD II (OBD 2): What are Readiness Monitors? and OBD II Monitor Drive Cycle Service are great examples).

      The quick answer is that if the computer in your car loses power for any reason, or if diagnostic trouble codes are cleared following repairs, you typically will have to drive your car between fifty to one-hundred miles (not minutes) before it will be ready to pass a smog inspection. It can take more or less miles than that, but fifty to one-hundred miles is the general rule of thumb.

      Reply
  27. Pingback: January 2017 California Smog Check FAQ | JUST SMOGS®

  28. Mae

    I am required to get a smog check on my 2007 VW Rabbit. The engine light was on so I took it to an Aamco Transmission before I get it smog checked. Aamco was able to detect two codes. I was told that I needed the gas cap replaced so I did. They reset the computer to clear the engine light on the dashboard. I went to a smog check station, and I was told to drive it for another 20 miles because they are getting, “OBD Not Ready/Incomplete”. So I drove another 30 miles, and ended up taking it to another smog check station where I was, and they also got the same error code of “OBD Not Ready or Incomplete”. I was told by that smog check station to take my car to a mechanic. I took my car to a mechanic, and they told me that I did not pass or fail the smog check, the print out only tells me that my car is not ready for the smog check, so they suggested for me to drive another 80 miles, and have it re-checked. How many miles do you have to drive your car in order for the smog test machines able to read by car’s computer? This is the first time I have encountered anything like this in regards to smog checks.

    Reply
    • Julius

      Hi Mae,

      I’m sorry you’re having trouble completing monitors on your 2007 VW Rabbit. If it makes you feel better, VWs are known for presenting a bit of a challenge when it comes to running monitors.

      First, let’s clear something up “OBD Not Ready or Incomplete” is not an “error”. It simply means that your vehicle’s on board diagnostic system (“The Computer”) is still checking things out.

      Each test “The Computer” runs on itself and its related systems requires that certain enabling criteria are met before the test can be run. If a test fails, the check engine light is turned on; otherwise, the tests run in the background and we normally don’t have to give them a second thought.

      However, in your case, since your VW needs to pass a smog inspection, you’re in a position to give them a lot of thought.

      While most cars will complete readiness monitors within 50 to 100 miles of a computer reset, some cars may require more driving. This is especially true if a monitor (really just a test) is on the verge of failure, or enabling criteria are not being met.

      The following drive cycle is recommended for your your 2007 Volkswagen Rabbit :

      – Switch the ignition on and start the vehicle.
      – Idle the vehicle for 2-3 minutes. This executes the O2S Heater, Misfire, Secondary AIR, Fuel Trim, and Purge system monitors.
      – Drive the vehicle at 45-55 mph for a continuous 7 minute period, avoid stopping. This executes the EVAP, O2S, Fuel Trim, and Misfire monitors.
      – Accelerate the vehicle to an engine speed of 5000 RPM (with automatic transmission use the tip-tronic mode) lift off the throttle until the engine speed is around 1200 rpm. This executes the fuel cut off
      – Accelerate the vehicle smoothly to 60-65 mph, cruise constantly for 5 min, this executes the Catalyst, O2S, Misfire, Fuel Trim, and Purge System monitors.
      – Decelerate and idle the vehicle again for 3 minutes. This executes the Misfire, Secondary AIR, Fuel Trim, and Purge system monitors.

      You may have to repeat this process several times. If you have access to a scan tool or code reader (Even a Harbor Freight code reader will do the trick), you can check for monitor completion as you go.

      Since all of the above can be difficult to pull off during normal Southern California driving conditions, I usually recommend a nice Saturday or Sunday morning drive when traffic is more manageable.

      Safe driving

      Reply
  29. Mae

    Thank you, Julius. I took it to a smog check station again for the third time, and I got the same result, “Not Ready” on the printout. I decided I will wait another week to return it to the smog check station. I have already spent $51.75 for the first test, and another $26.75 for the retest. The check engine light did not come back on. If the monitor on my car is the problem, how much does it usually cost to get a replacement monitor? I hope I am understanding everything.

    Reply
    • Julius

      Hi Mae,

      A monitor isn’t something that would go bad, or require replacement. Think of a monitor as a test, or process, in your car’s computer software that keeps an eye on (Monitors) your car’s emissions related systems and sensors. The monitor itself wouldn’t be the problem, instead it might help to take a look at the system or sensor being monitored. Does that make sense?

      Here’s what I would suggest:

      First try following the Drive cycle procedure I described in my previous reply. It often helps to let the car sit overnight before each attempt. That way the car is sure to perform a full cool down and warm up cycle.

      If the monitors do not run after several attempts at following the drive cycle (Remember that the cool down and warm up cycles are important), I would suggest taking the car to a mechanic that has experience working on Volkswagen. A good Volkswagen mechanic will have access to tools and diagnostic equipment that many shops wont.

      Have your mechanic check systems to the monitors that aren’t running. Very often one monitor (test) will be dependent on the results of another. For example the secondary air monitor may depend on the O2 sensor monitor. If the O2 sensor monitor isn’t running, your mechanic could check the O2 sensors, if the results are borderline correcting any O2 sensor related issues (Including exhaust leaks around the sensors) could be the key to getting the monitors to run. That’s just an example of how your mechanic could go about checking your vehicle. If the Secondary Air Monitor is the only one that isn’t running, he could check that system first.

      Again, performing the recommend drive cycle two or three times should hopefully do the trick. Let me know how it all works out.

      Reply
  30. Anne

    HI,
    My 2003 Mitsubishi Galant cannot be smogged because, they tell me, the OBD system in the car is not communicating with the smog-checking device. I took it in to check all electric wires; a loose one was fixed, and the dealership says the car can communicate. I then took it to smog-check–but the tech had the same problem as before, car cannot communicate with the CA state smog system.
    This is the third smog center that has tried to smog it. What more can I do to fix the OBD? Thanks.

    Reply
    • Julius

      Hi Anne,

      That’s a tough question to answer without actually seeing the connector on the car, but my guess is that one of the terminals is just loose enough that it’s completing contact with the scan tool in your mechanics shop, but not quite good enough for the smog machine.

      The only think that I can suggest off the top of my head is that you have your mechanic double check the diagnostic link connector in your vehicle, and ensure that all the terminals are secure and firmly in place. Sorry that I couldn’t be more help.

      Reply
  31. Corina Nash

    I took my 1997 infin i30. To the emmission in phx,Az..
    This vehicle has passed equipment expection and felt the emission test This vehicle has failed to communicate with the OBD emission testing equipment as per APA Guidance the vehicle fails the Arizona emissions OBD testing for no communication (OBD-ON BOARD DIAGNOSTIC OR VEHICLES COMPUTER)
    THEY CHECK ENG..LIGHT IS NOT ON…

    NEED HELP ON WHAT TO DO..

    Reply
    • Julius

      Hi Corina, I’m not familiar with the smog check program in Arizona, but based on your comment I assume that you need to have the cause of the on board diagnostic communication failure repaired. If you don’t have a mechanic, perhaps the inspection station that conducted your emissions test could help you locate a shop in your area.

      Reply
  32. Pingback: Emissions learn cycle ODB2 - Pontiac G6 Forum

  33. Ernest

    I have a 2011 honda fit, took it for smog. Smog guy says the cat sensor is not ready, and to drive it around some more week later ovee a hundred miles still not ready. The drive cycle is impossible. Don’t know what to di

    Reply
    • Julius

      Drive cycles can be challenging, but the one for your car shouldn’t be too bad. At least, I haven’t seen a lot of people having trouble with 2011 Honda Fits.

      I’d suggest a couple of things.

      First make sure that you’re letting the car warm up completely before you start the drive cycle. We’ll typically let them idle for ten minutes before we even get started.

      Second try running the drive cycle early on a Saturday or Sunday when traffic is light. The key to most if these drive cycles is even acceleration and steady cruise. Avoid unnecessary braking and acceleration.

      If the monitor just wont run to completion, a component or sensor on the verge of failure might be the problem. The good news is that many emissions related components may still be under warranty on your 2011 Fit.

      If you’re not too far from Huntington Beach, you can always bring the vehicle in to Just Smogs. We have great success diagnosing monitor issues and running monitors to completion. You can make an appointment at (714) 596-1019.

      Reply
      • Lynn Strother

        I have a 2011 Honda Fit Sport and had the same problem. At the smog station, they told me to drive on the freeway for 60 miles. I did that, took it back, and it was still not ready. Then I called the service department at the Honda dealership. The service guy told me that the way to do it was to drive at exactly 65 miles per hour for 10 miles. I got up early this morning (around 6:30 a.m.) when the freeway traffic was pretty light eastbound on the 105, and was able to do 10 miles, using cruise control, at 65 mph. I took it back to the smog test place, and it checked out as ready. Mission accomplished. The dealership and smog place told me that they would do the drive cycle for $130 to $150. So I’m feeling smug about smog!

        Reply
  34. pablo

    Hi I am Paul …. I have a Ford e350 superduty 2003, not pass the smoog by sensor OBD II, they recommend me drive cicle, but I know what change new … not understand well the dryve cicle …. I do before back to smoog ???, what will happen? ….. anyway I have to re-Spain 10 days and is essential for the name change in the DMV …… I would come great advice urgent please …… sorry for faults because I am Spanish and i’m not entirely formed in English still …… thanks

    Reply
    • dewok Post author

      Hi Paul, if you recently purchased this vehicle in California, I would recommend bringing it back to the seller and have them deal with the smog check. By law the seller is required to smog their vehicle within 90 days of sale.

      If this is not the case, I recommend following some of the drive cycle instructions found on this site: allow vehicle to warm up at idle. Drive steady around town and then on the highway at a steady speed for about 10 minutes. If there is nothing wrong with the vehicle, the monitors should set within 50-100 miles of steady mixed driving.

      Reply
  35. luis mendoza

    I have a 2005 infiniti G35 coupe and did not pass smog due to catalytic converter monitor status as ” not ready” I’ve driven it for about 150 miles and no change. what should I do ? Thank you in advance!

    Reply
    • dewok Post author

      Hi Luis,

      Catalyst drive cycle for 2005 Infiniti G35:

      Start engine in the morning when cold and allow vehicle to warm up at idle (about 10 minutes). Drive @ 53-60mph for 3-5 minutes. Repeat if necessary.

      Good luck!

      Reply
  36. Lilli

    Hi Julius,
    I’m trying to get my 2000 Infiniti i30 to pass the CA smog inspection. The failed paperwork shows Under the section of the test Emission Control Systems Functional Control Results, the results indicate pass but states Liquid Fuel Leak Check result Not Ready OBDII. The next section is titled: OBDII Monitors Not Ready – In this section it states Catalyst. We tried driving the car over 200 miles and we also tried the Infiniti drive cycle, but I just noticed we did not do the last part of the drive cycle as listed in the infinity book where you rev the engine for several minutes. We only learned about the rev the engine part after we had completed the drive cycle. Any suggestions on what I can do to get this car to pass the smog test?

    Reply
    • dewok Post author

      Hi Lilli,

      The 2000-2001 Infiniti i30 have difficulty completing all monitors during normal driving. It is a known issue with these vehicles. Sometimes the 200-2001 I30 Failure to set catalyst monitor is due to a catalytic converter issue. Only OEM scan tool shows OBD catalyst code. The State of California advises to test the catalyst and replace if defective. If the converter is not defective, drive the vehicle per Infiniti factory drive cycle (I know it’s difficult).

      Good Luck!

      Danny
      JUST SMOGS

      Reply
  37. John Ruegg

    On a 2002 Diesel gmc my comp monitor won’t show ready.. Could it be because the fuel gauge has problems? It shows low fuel and sometimes bonces from empty to full

    Reply
    • Danny Post author

      Hi John,

      Please check the underhood emission label to see if your diesel is California or Federal certified. Some Federal diesel vehicles over 8,500 GVWR were not built to comply with OBD-II or Fed OBD standards. BAR-OIS will ignore incomplete continuous monitors.

      Danny
      JUST SMOGS

      Reply
  38. Nicole Daniels

    So I have 96 gmc Yukon and I had a misfire code as well as the purge valve . Well after research and replacing parts those code’s cleared themselves. Now when I plug my obdII reader in the EGR and CAT flash red but trucks now throwing the check engine light on anymore. Will it still pass smog. I did my drive cycle and no codes but on the reader it shows CAT and EGR in red

    Reply
    • dewok Post author

      Hi Nicole,

      If Catalyst and EGR monitor are incomplete, it will not pass smog. As soon as one of the two completes ready (without DTCs), it will be ready for an inspection.

      Reply
  39. Pingback: 1114 My Rant about the State’s Emissions Test | Find the Factors

  40. Bruce Falkenhagen

    Do you have the best drive cycle for a 1999 Jaguar XK8 that is failing the EVAP and CCM monitors? I notice that you have some different ones for some specialty vehicles in the comments, and I can’t seem to clear the CCM one.

    Reply
    • dewok Post author

      Hi Bruce,

      Some european makes can be challenging when it comes to drive cycles. I’ve noticed that for most vehicles, CCM monitors complete on start up. On rare occasions, CCM monitor issues require a computer reflash. Unfortunately, I don’t have direct access to Jaguar’s exact drive cycle procedures.

      Sorry we couldn’t be more of help.

      Danny
      Just Smogs

      Reply
  41. Kia

    Hi I have a 2006 Cadillac SRX from out of state. Took it to get smog tested in Orange County California and it failed. The VIR says (OBD II Fail) and (OBD Bulb Check Fail). The technician didn’t give me any information, just said go to a mechanic. Before the test, the car hadn’t been operated for 3 weeks and had just arrived from being shipped from out of state. I didn’t know I should’ve driven it more first. I’m not sure what my next step should be so any thoughts are greatly appreciated. Thank you!

    Reply
    • dewok Post author

      Hello,

      Most likely a “Not Ready” fail. If the vehicle had a dead battery after the 3 weeks of sitting, the readiness monitors would have been cleared. Drive some more, and you should be OK. If the VIR states that something else failed, reach out to us with a follow up question.

      Reply
    • Qu

      Hi Kia,

      Did this issue get fixed? Can you share how it was fixed? Is it easy for self-fix?

      I also got “OBD Bulb Check” as FAIL.

      Plus, got the following codes on the honda 2000 v6:
      p0300
      p0301
      p0302
      p0303
      p0304
      p0305
      p0740

      Thank you!

      Reply
  42. Paul

    My mother has a 2002 Subaru Legacy. Her CEL came on and code P0113 indicated bad IAT. I replaced the IAT and the CEL went off. A month or so later she tried to smog the car and the smog technician tells her the OBD hasn’t reset and is not “ready” even though no CEL is present. He advised us to drive it another 100 miles since the IAT was recently replaced. She did and she had it rechecked and same thing. He then advised us to perform this ridiculous “resetting” procedure – driving, stopping, different speeds etc…took a good hour. Rechecked and still not “ready”. Took it to dealership and they told her she needs a new Catalytic Converter for $1800! Again, No CEL and car runs perfect. What’s going on? Any advice is greatly appreciated.

    Reply
    • dewok Post author

      Hi Paul,

      Sounds like the Subaru has an incomplete “Catalyst” monitor. So, either there is a “pending DTC” indicating a defective catalytic converter (ie P0420) or the vehicle is in a “gray” area- the catalyst monitor isn’t defective enough to set a DTC illuminating the MIL, but it isn’t operating well enough to set “Ready” with no DTC(s) (indicating a good converter). If everything “upstream” is working correctly (sensors, no exhaust leaks, etc) then the dealer may be right. I recommend checking to see if there are aftermarket converters available. Aftermarket converters usually cost much less than OEM.

      Reply
  43. raj

    i got smog check 2000 model corolla and it says test is incomplete obdii catalyst says evaporative system is i am passed smog or not. Reason for asking is 2000 model and above are excluded evap monitor

    Reply
  44. Debra

    I have been driving for hundreds of miles to get my CAT ready to test for smog in CA. I have a 2001 VW New Beetle. Car throws CO2 sensor code but my tech says he ran it through and it’s CO2 passed. If CAT won’t “ready” does that mean you definitively new a new one? Thanks you for responding.

    Reply
    • dewok Post author

      Hi Debra,

      Your mechanic definitely needs to address any fault codes prior to attempting a drive cycle. If there is a DTC associated with an oxygen sensor, the CAT monitor may not run to completion.

      Reply
      • Debra Mauritson

        All systems “ready” including O2 sensors; it’s just the CAT turns ready and then flips off within seconds. I don’t have a mechanic I trust anymore and hate to jump in and spend $400 on a new CAT wondering all the while if it will be the solution to passing smog. I’m running out of options and time. Car runs great; eats gas but always has. Nothing visible comes out of the exhaust. Wish I lived in any state but CA.

        Reply
        • dewok Post author

          Hi Debra,

          I personally have never seen a monitor set ready and then switch back to not ready. Sounds like a computer/programming problem. I would check with a certified independent mechanic or the dealership prior to replacing the catalytic converter. Please let us know how it turns out.

          Reply
  45. Jay

    All I gota say is THANK YOU ALL for all the info and recommendations no matter what vehicle needs this process. At the end i used the cata cleaner and that was the solution to my issue. Similar to the issues you all have encountered at some point. The cata cleaner did its magic on my 2007 nissan altima. It first completed the EVAPORATIVE sys, and 2 weeks later some way somehow cuz I know I wasnt doing the drive cycle properly, it completed the catalyst sys so thank you once again and good luck to the rest.

    Reply
  46. Christian Huebner

    I have a 2000 Chevy Camaro SS. After sensor repair and swapping the AIR valves and driving for >100 miles all the Smog Readiness monitors were complete (torque app). Took me a while to clear EVAP but eventually it did. That was yesterday night. This morning I went to the Smog test only station and the guy told me and showed me on the screen that pretty much everything was incomplete again. I think misfire and fuel system were complete, everything else was incomplete. I drove to the office and checked again with the Torque app. Now evap, secondary air, o2 sensor heater and EGR are still incomplete. My battery is strong and starts the car instantly. No signs of voltage drop anywhere. Do you have any insight on why the system may have reset itself? There are no failed values in there, only incomplete.

    Reply
  47. Alejandro Soriano

    I drive a 2004 4×4 f250 6.0 diesel truck I’ve taken my truck for smog and they say that it ain’t reading any information from the truck but my mechanic puts his scanner and it communicates with the truck any suggestions?

    Reply
    • dewok Post author

      Hi Alejandro,

      Has your vehicle ever had a PCM tune or tuner installed?

      If not, I would ask your current smog check station which OIS analyzer they are using (Smog Daddy, Imclean, etc). There are a handful of manufacturers. You can try another shop that is using a different analyzer.

      A couple of years ago, we had a similar issue with a particular vehicle. We tried reading the OBD on a different analyzer and it worked fine.

      Reply
      • alejandro soriano

        I’ve taken my truck 2 2 spots and doesn’t show any codes the only thing it says it not ready so they tell me to drive my truck I’ve driven truck for more then six hundred miles and it keeps saying that it is not ready.

        Reply
        • dewok Post author

          Hi Alejandro,

          It might be time to take it to the dealership or a reputable test & repair station.

          Reply
  48. Ed Locatelli

    I have a similar issue now. I drive a 2010 dodge challenger and I pass everything except the 02 Sensor. No matter how or how much i drive, it still says not ready. Repair places don’t want to replace sensor because check engine light is not on. I’m not sure what else to do.

    Might be time to get a new car

    Reply
    • dewok Post author

      Hi Charles,

      Yes, manual transmission vehicles may require specific drive cycle procedures. Primarily keeping the RPM low (Below 3,000). We’ve had our best luck completing stubborn readiness monitors when shifting below 2,500 RPM.

      Reply
  49. Lee Ann

    I have a 2010 Chrysler Town and Country. It was sitting undriven for 6 months. The battery was stone dead so I had to replace it yesterday. I took it to get smogged today and was told that it failed the OBDII test and the OBD bulb check and then gave a service fault code of U110C. The check engine light was not on prior to be taking it to get the smog but it did turn on when I started it up to leave the smog place but was back off by the time I made the 2 mile trip back home. Any idea if this could be all caused because it was sitting to long or is it most likely a big issue somewhere?

    Reply
    • dewok Post author

      Hi Lee Ann,

      The U110C fault code is a communication failure between the BCM and the PCM on the fuel level bus line. Without having the vehicle here, I can’t say if it was caused by sitting too long or it’s a bigger issue. Based on what I’m reading online, a factory scan tool (dealership, most likely) will be required for a precise diagnosis.

      Reply
  50. Robin Desowitz

    I have a 2013 Volt which I almost never drive on gas (109500 miles 332 gallons of gas) it now needs to be smogged but it failed due to lack of driving on gas!!! How far do I need to torture myself driving on gas before getting it tested again????

    Reply
    • dewok Post author

      Hi Robin,

      I have limited experience with Volts. An educated guess would be 50-100 miles of driving.

      Good luck!

      Reply
  51. Benjamin

    Hey I have a 2001 Toyota Camry. I have no check engine light on but my catalytic converter shows up not ready… I’ve drove 1500 miles since I’ve tried to get a smog. Any suggestions?

    Reply
    • dewok Post author

      Hi Benjamin,

      Based on how much you’ve driven, I assume at some point you drove in the proper conditions to complete the catalyst drive cycle.
      At this point I would bring your Toyota to a mechanic for further diagnosis of oxygen sensors, catalytic converters, etc.

      Reply
  52. jim schofield

    Hi dewok, I have a 2007 Odyssey which failed smog due to lack of sensor data (battery replaced recently). Great answers above regarding general driving requirements to reset sensors. I checked I/M Readiness with a meter and got INC (incomplete) on the Evaporative systems monitor; all the rest were ok. Do you have any specific suggestions for a driving regimen to get this one to reset?

    Reply
    • dewok Post author

      Hi Jim,

      On a 2007 Odyssey if all monitors are ready except EVAP, you are good to go! As of right now, the vehicle will pass the OBD portion of the CA smog check.

      Reply
  53. Allen Tipoetts

    I have a 2003 Dodge Ram 2500 with the 5.9 Cummings and the NV5600 6 speed manual.
    It is failing the OBDII bulbs check,and the OBDII says fail on the paperwork from the smog check station. It is posted under the Emissions Control System Function Results on the paperwork from the smog station.

    I have had the ECM reflashed, but it is still failing.

    It’s a bit exhausting.

    Reply
    • dewok Post author

      Hi Allen,

      If everything was fixed (if applicable), the proper reflash was completed and a drive cycle was completed, it should pass OBD II portion of the smog check.

      There is a know OBD testability issue with 2003 Dodge Ram 2500 w/ 5.9L Cummings
      (BAR OBD Reference)

      Dodge 2003 Ram Truck 5.9L (Cummins diesel) [California certified]
      – MIL light is commanded on, but check engine light is not illuminated and no DTCs are stored
      – Vehicle design anomaly Recall campaign #K01 for ECM reflash applies to California certified vehicles only
      – Test normally. OIS ignores MIL Command if no DTCs are present on this vehicle Advise motorist of Recall Campaign #K01 if the vehicle is California certified

      If this doesn’t work for you, you can contact the BAR Referee

      Reply
  54. William

    My 2012 Lexus 250i went in got smog. The tech said he could not run the test because 2 ports were not working. What does that mean? And is it a costly repair?

    Reply
    • dewok Post author

      Hi William,
      I’m assuming he means two monitors are not ready. Your vehicle may just need a drive cycle.

      If there is something wrong with the vehicle’s OBD port, that will require a repair.

      Reply
    • dewok Post author

      Hi William,

      I thought that I already replied to this.

      I have a feeling that the technician meant to say that two monitors are not ready. Identify the two monitors (EVAP is ignored by the smog machine) and follow the warm up and driving instructions within this post.

      This shouldn’t cost you anything other than time and gas.

      Good luck

      Reply
  55. Maria Bayon

    I took my 2001 GMC 3500 Dually in for a smog test. The guy brought a computer reader over to the truck before he did smog test. It showed a red X next to Air. What does that mean? I had just spent over five thousand to have a transmission re-built because of a bad sensor and the red X wasn’t there before. Thanks for any information!

    Reply
    • dewok Post author

      Hi Maria,
      The red X simply means that the GMC’s computer hasn’t yet determined that the AIR injection system is working properly. Once your vehicle has completed the successful self test for the AIR system, it should be OK.

      After a major repair, such as a transmission, usually all monitors are incomplete because either the battery was disconnected, computer was cleared or the battery had died. This is absolutely normal.

      Reply
  56. Greg

    I have a 2003 GMC LB7 Diesel in California, everything is ready BUT the Continuous Component Monitor wont complete I had this happen 2 years ago and it finally just cleared after 1k miles, this year Im having the same issue but now at 2500 miles still not cleared. I don’t know what to do at this point.

    Reply
    • dewok Post author

      Hi Greg,

      The INCOMPLETE Continuous Component Monitor can be tricky on these diesel trucks. In our experience, either the vehicle needs to be driven (a lot) or the computer needs a reflash to the most current software.

      Perhaps check with your mechanic to see if there is a software reflash available and if they think it would help resolve the problem.

      Reply

Leave a Reply to KenCancel reply